+91 98677 24577
info@impactpvt.in
Plot No.101, College Phata, Panvel, Navi Mumbai

Aquinity²- P10

Aquinity² models produce ultra-pure water directly from tap water. The Aquinity² P10 ultrapure water system is equipped with reverse osmosis (RO) module to produce deionized water directly into an integrated 10l tank. In the next step Type, I grade water is produced with a polisher cartridge. The Aquinity² water purification system is available in different configurations (Reagent & Analytical) to meet the specific requirements of ultra-pure water for different applications.

Analytical is a version with a UV lamp for low TOC value. Life Science grade water with low endotoxin can be generated with a special final filter. An optional integrated TOC sensor allows the user to monitor the TOC content permanently online. Besides that, the Aquinity² can be configured as a bench top or bench-integrated system, where the control panel will mount on the wall.

Technical Specifications -

18.2 MOhm x cm | 0.055 µS/cm; Type I

- RESISTIVITY/CONDUCTIVITY

max. 8 L/h -

PRODUCTION RATE

< 10 ppb (Reagent) < 3 ppb (Analytical)-

-TOTAL ORGANIC CARBON (TOC)

Aquinity²- P10 Advantages -

COMPACT HOUSING
BIG TOUCHSCREEN
REMOTE SERVICE MODULE
MENUS AND WIZARDS EASY TO USE AND MISTAKE AVOIDING
FIXED AND FLEXIBLE DISPENSER
EASY ACCESS FOR CARTRIDGE EXCHANGE

Options

BENCH INTEGRATED CONFIGURATION (BI VERSION)

To save valuable benchtop space the system can be ordered as BI configuration. The system will be installed underneath the work bench and only the display and dispenser are mounted on the wall

WALL MOUNTED CONFIGURATION

To save valuable benchtop space the system can be ordered as wall mounted configuration. the whole system can be mounted on the wall with inclined display

IQ/OQ documents

Validation documents for water purification systems.

TOC-MONITORING (TI VERSION)

The TOC monitoring during production and intermittent measurements during non-use periods allows to check the organic content in water continuously. The TOC value is measured between 1 and 999 ppb and can be shown in the display to monitor organic impurities.

VOLUMETRIC DISPENSING

Upgrade of system with fixed and flexible dispenser for the series of AquaRO² 10 + 20 and EDI² 10 + 20.

memTap

To be integrated into an ultra pure water system with a max, flow rate of 2 L/min. Point of use dispense arm with integrated control unit. Two joint to move it horizontally and vertically allowing to fill containers up to 55 cm height. Volumetric dosing of ultra pure water allows filling of containers without the attention of user, dosing eange 0.1 – 99 L, variable input and storage of values, after volume has been dispensed system goes back to standby.

Specifications -

Technical Specifications -

1	ltrapure water quality	0.055 µS/cm; Type I
2	Resistivity	18.2 MegaOhm/cm
3	Total organic carbon (TOC)	< 10 ppb reagent, < 3 ppb Analytical
4	Dispensing flow rate	1.5 L/min
5	Production rate	8 L/min*
6	Bacteria	< 1 cfu/mL
7	Particulate	> 0.2 µm less than 1 particulate/mL
8	RNAse	< 1 pg/mL**
9	DNAse	< 5 pg/mL**
10	Dimensions, weight, power	504 x 340 x 535 mm, 16-20 kg, 110 - 230 V not possible to tap pure water *with microbiological final filter

Feed Water Requirements-

1	Type of feed water	Tap water
2	Feed water conductivity	< 1400 µS/cm
3	Inlet pressure	1.5 to 6 bar
4	Free chlorine	< 0.1 mg/L
5	Silt Density Inded (SDI)	< 3
6	pH	3 to 9
7	Temperature	5 to 25 °C

News & Updates

Gas shield solution developed for the aerospace

Building back a sustainable manufacturing sector

Our Materials